Search:
  Quote Basket  |  Sitemap  |  Imprint
  • Deutsch
  • English

DSCA47

Linearized Thermocouple Input Signal Conditioners, Bandwidth 3 Hz

Each DSCA47 thermocouple input module provides a single channel of thermo-couple input which is filtered, isolated, amplified, linearized, and converted to a high-level voltage output. Signal filtering is accomplished with a five-pole filter which provides 85dB of normal-mode rejection at 60Hz and 80dB at 50Hz. An anti-aliasing pole is located on the field side of the isolation barrier, and the other four poles are on the system side. After the initial field-side filtering, the input signal is chopped by a proprietary chopper circuit. Isolation is provided by transformer coupling, again using a proprietary technique to suppress transmis-sion of common mode spikes or surges.

The DSCA47 can interface to eight industry standard thermocouple types: J, K, T, E, R, S, B and N. Each module has cold junction compensation to correct for parasitic thermocouples formed by the thermocouple wire and input screw termi-nals on the module. Upscale open thermocouple detection is provided by internal circuitry. Downscale indication can be implemented by installing a 47 MW, ± 20% resistor between screw terminals 6 and 8 on the input terminal block.

Module output is either voltage or current. For current output models a dedicated loop supply is provided at terminal 3 (+OUT) with loop return located at terminal 4 (-OUT). The system-side load may be either floating or grounded.

Special input circuits provide protection against accidental connection of power-line voltages up to 240 VAC and against transient events as defined by ANSI/IEEE C37.90.1. Protection circuits are also present on the signal output and power input terminals to guard against transient events and power reversal. Power lines are secured to the module using screw terminals which are in pluggable terminal blocks for ease of system assembly and reconfiguration.

The modules have excellent stability over time and do not require recalibration, however, zero and span settings are adjustable up to ± 3% to accommodate

situations where fine-tuning is desired. The adjustments are made using potentiometers located under the front panel label and are non-interactive for ease of use.

Circuit diagram Dataforth DSCA47

Block Diagram DSCA47



PDF Downloads:


14 Modules for Type DSCA47:

ModuleInputDescription
DSCA47B-11 Type B DSCA47 Isolated Linearized Thermocouple Input Signal Conditioner with Voltage- or Current-Output
DSCA47E-08 Type E DSCA47 Isolated Linearized Thermocouple Input Signal Conditioner with Voltage- or Current-Output
DSCA47J-01 Type J DSCA47 Isolated Linearized Thermocouple Input Signal Conditioner with Voltage- or Current-Output
DSCA47J-03 Type J DSCA47 Isolated Linearized Thermocouple Input Signal Conditioner with Voltage- or Current-Output
DSCA47K-04 Type K DSCA47 Isolated Linearized Thermocouple Input Signal Conditioner with Voltage- or Current-Output
DSCA47K-05 Type K DSCA47 Isolated Linearized Thermocouple Input Signal Conditioner with Voltage- or Current-Output
DSCA47K-13 Type K DSCA47 Isolated Linearized Thermocouple Input Signal Conditioner with Voltage- or Current-Output
DSCA47K-14 Type K DSCA47 Isolated Linearized Thermocouple Input Signal Conditioner with Voltage- or Current-Output
DSCA47N-15 Type N DSCA47 Isolated Linearized Thermocouple Input Signal Conditioner with Voltage- or Current-Output
DSCA47R-09 Type R DSCA47 Isolated Linearized Thermocouple Input Signal Conditioner with Voltage- or Current-Output
DSCA47S-10 Type S DSCA47 Isolated Linearized Thermocouple Input Signal Conditioner with Voltage- or Current-Output
DSCA47T-06 Type T DSCA47 Isolated Linearized Thermocouple Input Signal Conditioner with Voltage- or Current-Output
DSCA47T-07 Type T DSCA47 Isolated Linearized Thermocouple Input Signal Conditioner with Voltage- or Current-Output
DSCA47J-02 Type J DSCA47 Isolated Linearized Thermocouple Input Signal Conditioner with Voltage- or Current-Output

Specifications

top
  • Input: Thermocouple Typ J, K, T, E, R, S, B and N
  • Output: 0V…10V / - 10V…+ 10V / 0mA…20mA / 4mA…20mA
  • Bandwidth 3 Hz
  • Isolation 1500 Vrms
  • Input protection 240 Vrms
  • Input Resistance 50 MOhm
  • Accuracy ± 0.07% to ± 0.16%
  • ANSI/IEEE C37.90.1 Input protection
  • CMR 160dB
  • True 3-way isolation
  • NMR: 95/85dB at 60/50Hz
  • Power Supply 15 bis 30 VDC
  • Operating Temperature Range -40°C … +80°C
  • Adjustability of +/-5 % Zero and span
  • 5-pol. Filtering
  • Dimensions 75 x 22.5 x 105 mm
  • DIN Rail Mounting
  • CE and ATEX certified, C-UL-US compliant
  • Special Solutions on request